Clips decking board WPC composite

Buy clips decking board WPC composite at Intergard?

Clips for decking board composite decking in anthracite, grey and brown. Package 100 pcs with screws stainless steel. + Size 5x2cm + Easy to assemble + Durable + Very stable + Maintenance friendly + Water and moisture resistant + No splinters + Colourfast PREFACE Preferably to be used on a paved surface. Bee application directly on garden soil always use pavement tiles under the lines as a foundation (Fig. 1). In that case first level the ground and possibly remove weeds and use “anti-root cloth” to prevent growth prevent new weeds as much as possible. around the terraces and keep the rails at least 3 cm clear of walls or obstacles. Around the length effect due to the influence of varying temperatures of the composite to be able to accommodate parts, you must use multiple parts in the to keep an opening in the longitudinal direction of the terrace between the ends of approximately 1 cm. Always use a saw blade for sawing the material with fine tooth. STEP 1 • Lay the rails (substructure) flat, each time with a maximum of 30 cm from each other (Fig. 6). Make sure that the terrace is slightly in the longitudinal direction of the terrace parts slopes down at a slight angle of inclination of approximately 1 cm per linear metre so that the rainwater flows off the terrace. At the beginning and end every time install two beams at a center distance of 18 cm. TIP: Keep terrace boards 2 - 3 cm longer, after installation with a circular saw shorten the correct length and then mount the finishing profile. This provides an additional tight finish. STEP 2 • Place a finishing profile against the beginning of the rows (A-horizontal). (A-vertical) (Fig. 2). • Saw this finishing profile in a “false” miter. Note: do this according to the drawing (Fig. 7 and 8) in order to be able to handle the finishing profile on the so-called “head end” afterwards let it close. Do this only according to the drawing (Fig. 7 and 8). STEP 3 • Now place the first terrace section (B). Make sure that the brass of the finishing profile and the groove of the decking fit together and connect properly. • Then screw the finishing profile to it at least every 40 cm decking with the supplied long screws in the specified position v-grooves. Pay attention to the power of your screwdriver (Fig. 3). Tip: for extra strength, the horizontal rails can be fitted with angle irons screwed onto the vertical finishing profile (Fig. 9). STEP 4 • When the first part is laid, place on each line, in the groove of it decking, a clip (C). Make sure they fit snugly and then screw the clips loose/tighten on the line with the supplied short screws (Fig. 4). You can now install your second decking and repeat the above until the desired one size of your terrace has been reached. After complete assembly of the terrace, all Tighten screws and clips (pay attention to the power of your screwdriver). STEP 5 • After the last terrace section, finish with a finishing profile (A-vertical). both the long side and the so-called “head side”. Now saw to connect it profile on the longitudinal side in “false” miter. ATTENTION: do this according to the drawing (Fig. 7 and 8) for the finishing profile afterwards on the so-called "head end". Please note that the rails (A-horizontal) are cut to the correct length, so that the decking protrudes slightly (approx. 8 mm) and the finishing profile can connect properly (Fig. 5). Then screw the finishing profile to the terrace part every 40 cm with the long screws supplied indicated v-grooves (Fig. 5). TIP: An extra tight and firm attachment of the finishing profile is possible be achieved if you place another one at right angles to the ends of the bottom rail bottom rail, using angle irons such as described in step 3. In that case the bottom lines 50 + 8 = 58 mm shorter than the end of the last deck. After placement of the last terrace part, the finishing profile can then become good secured (Fig. 10). Before you install the finishing profile on the so-called "head end" confirmed the following is important: • Make sure that you “turn” the profile in relation to the profile on the longitudinal side before you cutting (Fig. 6). • Then saw according to the drawing (Fig. 7 and 8) to connect it finishing profile for the “head end” in “false” miter. • Then screw the finishing profile to the underlying profile every 40 cm align with the supplied long screws in the indicated position v-groove (Fig. 6). The terrace parts are profiled on one side and brushed flat on one side to be applied according to your preference. Pay attention to the power of your screwdriver. The terrace parts are suitable for use as a terrace part under normal conditions conditions, provided laying instructions are observed. Not suitable for load-bearing structures. Store flat to avoid deformation